STM32MP157x-DKx - hardware description

This article provides an overview of STM32MP157x-DKx Discovery kits.

Article purpose

This article briefly describes:

what are the different components present on the board
how to connect the board to external material
how to configure the board for boot
what are the configurations of the connector pins

This article is valid for the {{#vardefine:info|}}{{#vardefine:typ|}}{{#vardefine:info|}}STM32MP157A-DK1{{#var:typ}} {{#var:info}}, {{#vardefine:info|}}{{#vardefine:typ|}}{{#vardefine:info|}}STM32MP157D-DK1{{#var:typ}} {{#var:info}}, {{#vardefine:info|}}{{#vardefine:typ|}}{{#vardefine:info|}}STM32MP157C-DK2{{#var:typ}} {{#var:info}} and {{#vardefine:info|}}{{#vardefine:typ|}}{{#vardefine:info|}}STM32MP157F-DK2{{#var:typ}} {{#var:info}} Discovery kits: the part numbers are specified in the STM32MP15 microprocessor part numbers article.

This article is only an introduction to the STM32MP157x-DKx Discovery kits. Detailed information can be found in the STM32MP157x-DKx discovery board user manual.

Board assembly

STM32MP157x-DKx - board assembly

Board overview


Position	Description
1	MB1272 motherboard
2	MB1407 daughterboard DSI display (480x800 pixels): only for the {{#vardefine:info\|}}{{#vardefine:typ\|}}{{#vardefine:info\|}}STM32MP157C-DK2{{#var:typ}} {{#var:info}} and {{#vardefine:info\|}}{{#vardefine:typ\|}}{{#vardefine:info\|}}STM32MP157F-DK2{{#var:typ}} {{#var:info}} Discovery kits
3 (CN15)	microSD card

文件:STM32MP157x-DKx front side 1.jpg

STM32MP157x-DKx Discovery kit front side (first angle)
STM32MP157C-DK2 shown here (picture is not contractual)


Position	Description	Position	Description
10 (U5)	DDR3L 16 bits	11 (CN5)	2 USB Type-A (host)
12 (U13)	STM32MP157x 12x12	13 (U14)	HDMI
14 (CN7 and U12)	USB Type-C (DRP)	15 (CN8 and (U18)	Ethernet
16 (B1)	Wakeup button	17 (CN10)	Audio headset
18 (U20)	Audio codec (Cirrus CS42L51)	19 (B2)	Reset button
20 (LD5)	User LED (green)^{[LEDs 1]}	21 (B3)	User button (USER1)
22 (LD6)	User LED (red)^{[LEDs 1]}	23 (B4)	User button (USER2)
24 (LD7)	User LED (orange)^{[LEDs 1]}	25 (LD8)	User LED (blue)^{[LEDs 1]}
26 (CN11 and U19)	USB micro-B (ST-LINK/V2-1)	27 (LD4)	ST-LINK/V2-1 LED (bicolor)^{[LEDs 2]}
28 ('CN12)	ST-LINK/V2-1 DFU	29 (CN9)	HDMI connector

文件:STM32MP157x-DKx front side 2.jpg

STM32MP157x-DKx Discovery kit front side (second angle)
STM32MP157C-DK2 shown here (picture is not contractual)


Position	Description	Position	Description
10 (U5)	DDR3L 16 bits	11 (CN5 and U7)	2 USB Type-A (host)
12 (U13)	STM32MP157x 12x12	13 (U14)	HDMI
14 (CN7 and U12)	USB Type-C (DRP)	15 (CN8 and (U18)	Ethernet
30 (LD1)	USB Type-A LED (red)^{[LEDs 3]}	31 (CN2)	GPIO expansion
32 (U4)	PMIC (STPMIC1A)	33 (CN4)	DSI LCD connector
34 (LD3)	Ethernet LED (green)^{[LEDs 4]}	35 (CN6)	USB Type-C (power 5V-3A)
36 (LD2)	Power LED (green)^{[LEDs 5]}	37 (U8)	}}{{#vardefine:typ\|}}{{#vardefine:info\|}}STM32MP157C-DK2{{#var:typ}} {{#var:info}} and {{#vardefine:info\|}}{{#vardefine:typ\|}}{{#vardefine:info\|}}STM32MP157F-DK2{{#var:typ}} {{#var:info}} Discovery kits
40 (CN13)	Arduino Uno connector (socket 10x1)	41 (CN14)	Arduino Uno connector (socket 8x1)

文件:STM32MP157x-DKx back side.jpg

STM32MP157x-DKx Discovery kit back side
STM32MP157C-DK2 shown here (picture is not contractual)


Position	Description	Position	Description
40 (CN13)	Arduino Uno connector (socket 10x1)	41 (CN14)	Arduino Uno connector (socket 8x1)
42 (LD9)	Arduino LED (green)	43 (SW1)	Boot mode selection
44 (CN16)	Arduino Uno connector (socket 8x1)	45 (CN17)	Arduino Uno connector (socket 6x1)

Details about some LEDs:

↑ ^1.0^1.1^1.2^1.3 LD5, LD6, LD7, LD8: some user LEDs are used to reflect the system activity, while the others are left free to be used by the application, as explained in LEDs and buttons on STM32 MPU boards article
↑ LD4: flashes red if ST-LINK/V2-1 connection not established, else green
↑ LD1: turns red if USB Type-A connection established
↑ LD3: flashes green when Ethernet connection established
↑ LD2: turns green if power connection established

Board connection

The connections shown in the picture below are the ones recommended to start with the STM32MP157x_DKx Discovery kits. As shown in the board overview, other connectors are available for these boards (for example HDMI). STM32MP157x-DKx - board connections

Boot related switches

The following table defines the different combination of the boot mode selection switches:

"Boot 1" is grounded (always 0) on the Discovery kits

Boot modes
Boot mode	Boot 0	Boot 2
Forced USB boot for flashing	0	0
Not supported	1	0
Engineering boot	0	1
microSD card	1	1

Below the corresponding configurations of the boot related switches (SW1 on the board overview picture):

文件:STM32MP157x-DKx boot switches forced USB.png

Forced USB boot for flashing

文件:STM32MP157x-DKx boot switches engineering mode.png

Engineering boot

文件:STM32MP157x-DKx boot switches microSD card.png

Boot from microSD card

GPIO mapping

GPIO expansion connector

The pins of the GPIO expansion connector (CN2 on the board overview picture) are described in the following table:

GPIO expansion connector
Function	STM32 pin	Pin	Pin	STM32 pin	Function
3V3	-	1	2	-	5V
GPIO2 / I2C5_SDA	PA12	3	4	-	5V
GPIO3 / I2C5_SCL	PA11	5	6	-	GND
GPIO4 / MCO1	PA8	7	8	PB10	GPIO14 / USART3_TX
GND	-	9	10	PB12	GPIO15 / USART3_RX
GPIO17 / USART3_RTS	PG8	11	12	PI5	GPIO18 / SAI2_SCKA^{[EX 1]}
GPIO27 / SDMMC3_D3	PD7	13	14	-	GND
GPIO22 / SDMMC3_CK	PG15	15	16	PF1	GPIO23 / SDMMC3_CMD
3V3	-	17	18	PF0	GPIO24 / SDMMC3_D0
GPIO10 / SPI5_MOSI	PF9	19	20	-	GND
GPIO9 / SPI5_MISO	PF8	21	22	PF4	GPIO25 / SDMMC3_D1
GPIO11 / SPI5_SCK	PF7	23	24	PF6	GPIO8 / SPI5_NSS
GND	-	25	26	PF3	GPIO7
I2C1_SDA^{[EX 2]}	PF15	27	28	PD12	I2C1_SCL^{[EX 2]}
GPIO5 / MCO2	PG2	29	30	-	GND
GPIO6 / TIM5_CH2	PH11	31	32	PD13	GPIO12 / TIM4_CH2
GPIO13 / TIM3_CH2	PC7	33	34	-	GND
GPIO19 / SAI2_FSA^{[EX 1]}	PI7	35	36	PB13	GPIO16 / USART3_CTS
GPIO26 / SDMMC3_D2	PF5	37	38	PI6	GPIO20 / SAI2_SDA^{[EX 1]}
GND	-	39	40	PF11	GPIO21 / SAI2_SDB^{[EX 1]}

↑ ^1.0^1.1^1.2^1.3 The SAI2 is shared between the audio codec and the GPIO expansion connector. By default, the SAI2 is connected to the audio codec thanks to Solder Bridge SB13, SB14, SB15, and SB16: more details in the STM32MP157x-DKx discovery board user manual.
↑ ^2.0^2.1 Warning: the I2C1 is used to communicate with several on-board peripherals, but is also available on the GPIO expansion connector. So, it is important to ensure that new components added on the I2C1 connection will not disturb the bus behavior.

Arduino Uno connector

The pins of the Arduino Uno connector are described in the following table:

Arduino Uno connector

Socket 10x1 (CN13)
Pin names	Signal name	STM32 pin	Comment
1	ARD_D8	PG3	IO
2	ARD_D9	PH6	TIM12_CH1
3	ARD_D10	PE11	SPI4_NSS and TIM1_CH2
4	ARD_D11	PE14	SPI4_MOSI and TIM1_CH4
5	ARD_D12	PE13	SPI4_MISO
6	ARD_D13	PE12	SPI4_SCK
7	GND	-	GND
8	VREFP	-	VREF+
9	ARD_D14	PA12	I2C5_SDA
10	ARD_D15	PA11	I2C5_SCL

Socket 8x1 (CN14)
Pin names	Signal name	STM32 pin	Comment
1	ARD_D0	PE7	UART7_RX
2	ARD_D1	PE8	UART7_TX
3	ARD_D2	PE1	IO
4	ARD_D3	PD14	TIM4_CH3
5	ARD_D4	PE10	IO
6	ARD_D5	PD15	TIM4_CH4
7	ARD_D6	PE9	TIM1_CH1
8	ARD_D7	PD1	IO

socket 8x1 (CN16)
Pin names	Signal name	STM32 pin	Comment
1	NC	-	NC (reserved for test)
2	3V3	-	IOREF 3V3
3	NRST	NRST	NRST
4	3V3	-	3V3
5	5V	-	5V
6	GND	-	GND
7	GND	-	GND
8	VIN	-	Not connected

Socket 6x1 (CN17)
Pin names	Signal name	STM32 pin	Comment
1	A0	PF14	ADC1_IN0
2	A1	PF13	ADC1_IN1
3	A2	ANA0	ADC1_IN6
4	A3	ANA1	ADC1_IN2
5	A4	PC3 / PA12	ADC1_IN13
6	A5	PF12 / PA11

User buttons and LEDs

The GPIO assignments for the user buttons and LEDs are described in the following table. Refer to LEDs and buttons on STM32 MPU boards article to get information on the functional mapping for each one.

GPIO for user buttons and LEDs
LED color and label	Button label	GPIO
Green LD5 (*)	USER1 (*)	PA14
Red LD6 (*)	USER2 (*)	PA13
Orange LD7	-	PH7
Blue LD8	-	PD11

(*) Both a LED and a button are connected to the same GPIO, with inverted logic for the LED control (so the LED is switched on when the GPIO output is set to low).

[User_LEDs-1] 1.0^1.1^1.2^1.3 LD5, LD6, LD7, LD8: some user LEDs are used to reflect the system activity, while the others are left free to be used by the application, as explained in LEDs and buttons on STM32 MPU boards article

[2] LD4: flashes red if ST-LINK/V2-1 connection not established, else green

[3] LD1: turns red if USB Type-A connection established

[4] LD3: flashes green when Ethernet connection established

[5] LD2: turns green if power connection established

[SAI2-6] 1.0^1.1^1.2^1.3 The SAI2 is shared between the audio codec and the GPIO expansion connector. By default, the SAI2 is connected to the audio codec thanks to Solder Bridge SB13, SB14, SB15, and SB16: more details in the STM32MP157x-DKx discovery board user manual.

[I2C1-7] 2.0^2.1 Warning: the I2C1 is used to communicate with several on-board peripherals, but is also available on the GPIO expansion connector. So, it is important to ensure that new components added on the I2C1 connection will not disturb the bus behavior.

[LEDs 1]

[LEDs 2]

[LEDs 3]

[LEDs 4]

[LEDs 5]

[EX 1]

[EX 2]

匿名

搜索

STM32MP157x-DKx - hardware description

名字空间

更多

页面选项

目录

Article purpose

Board assembly

Board overview

Board connection

Boot related switches

GPIO mapping

GPIO expansion connector

Arduino Uno connector

User buttons and LEDs

导航

导航

所有产品

Wiki工具

Wiki工具

匿名

搜索

STM32MP157x-DKx - hardware description

目录

Article purpose

Board assembly

Board overview

Board connection

Boot related switches

GPIO mapping

GPIO expansion connector

Arduino Uno connector

User buttons and LEDs

导航

Wiki工具

页面工具

分类