STM32MP15 TF-A

来自百问网嵌入式Linux wiki
Wiki（讨论 | 贡献）2020年11月2日 (一) 15:21的版本

Article Purpose

本节详细介绍了从源构建TF-A并将其部署到目标上的过程。
构建示例基于OpenSTLinux环境：

  • 开发人员包
  • 程序的发行包

Overview

TF-A是ST受信任引导链的FSBL。它必须根据您的平台进行配置或更新。

TF-A的交叉编译仅在需要修改时才需要。 默认情况下，在入门包中，TF-A映像的名称为： tf-<board>-trusted.stm32.
进行更改后，您必须重建TF-A并使用此新映像更新引导设备的所有FSBL分区。 第二个FSBL映像用作备用映像。

构建过程将创建完整的STM32映像，该映像可用于Flash集成特定的header.

此受信任的固件-A映像包含设备树，BL2和BL32级。
这些二进制文件是在构建过程中一步完成的。

Atf.stm32.png


Developer Package

Install sources

开发包包含OpenSTLinux和TF-A源： TF-A Installation

Official source tree

Warning.png STM32MP1平台尚未完全上行。 因此此存储库中的功能不可用

从官方GitHub下载源代码 

 PC $> git clone https://github.com/ARM-software/arm-trusted-firmware.git

从内部git下载源代码 

 PC $> git clone ssh://gerrit.st.com:29418/mpu/oe/st/tf-a.git

Build Process

Initialise the cross compile environment

Setup Cross compile environment

TF-A Build flags

For ecosystem release ≥ v1.2.0{{#set:Ecosystem release=revision of a previous flow 1.2.0}}
强制性标志：

  • ARM_ARCH_MAJOR=7: 要针对的ARM体系结构的主要版本（STM32MP15基于ARMv7体系结构）
  • ARCH=aarch32: 指定要构建的aarch32体系结构
  • PLAT=stm32mp1: 构建一个stm32mp1平台
  • DTB_FILE_NAME=<fdt file name>.dtb: 必须定义此名称以构建适当的目标并将正确的DTB文件包括到最终文件中
  • AARCH32_SP=<monitor>
    • sp_min: 如果需要，可构建BL32安全监视器
    • optee: 不要包括BL32，并准备BL2以应对optee专用的负载，这也需要使用'STM32MP_BOOT_ONLY = 1'选项进行构建。

可选标志：

  • STM32MP_BOOT_ONLY=1: 构建所有存储驱动程序支持（串行除外）（不支持stm32_programmer）。OP-TEE模式必需。
  • STM32MP_FLASHLOADER_ONLY=1: 仅构建串行链接驱动程序支持（UART / USB）和stm32_programmer支持。
  • DEBUG=1: 在所有二进制文件中添加调试信息
  • V=1: 打印详细的编译痕迹
  • STM32MP_FPGA=1: 包括FPGA特定代码（与板不兼容）
  • STM32MP1_TEST=1: 启用特定SMC以进行测试（强制验证）


For ecosystem release v1.1.0{{#set:Ecosystem release=revision of a previous flow 1.1.0}}

Mandatory flags:

  • ARM_ARCH_MAJOR=7: the major version of ARM Architecture to target (STM32MP15 is ARMv7 architecture based)
  • ARCH=aarch32: specify aarch32 architecture to be built
  • PLAT=stm32mp1: builds an stm32mp1 platform
  • DTB_FILE_NAME=<fdt file name>.dtb: this must be defined to build the proper target and include the correct DTB file into the final file
  • AARCH32_SP=<monitor>
    • sp_min: builds the BL32 secure monitor if required
    • optee: do not include BL32 and prepare BL2 for optee-specific load

Optional flags:

  • DEBUG=1: add debug information in all binaries
  • V=1: print verbose compilation traces

<securetransclude src="ProtectedTemplate:InternalInfo" params="* STM32MP_FPGA'"`UNIQ--nowiki-00000000-QINU`"'1: include FPGA specific code (not compatible with board)

  • STM32MP1_TEST'"`UNIQ--nowiki-00000000-QINU`"'1: enable specific SMC for test purposes (mandatory for validation)"></securetransclude>

Build command

From the Developer Package tarball, a Makefile.sdk is present and must be used to build the target. It automatically sets the proper configuration for the TF-A build.

 PC $> make -f Makefile.sdk TF_A_CONFIG=trusted TFA_DEVICETREE=stm32mp157c-<board>

The latest version of the helper file is also available in this user guide: README.HOW_TO.txt

Warning.png The DTB_FILE_NAME flag must be set to select the correct board configuration.

The device tree file for the target must be located in fdts folder (stm32mp157c-<board>.dts)

If no Makefile.sdk exists, you must add your own environment flags: 

 PC $> unset LDFLAGS;
 PC $> unset CFLAGS;
 PC $> make ARM_ARCH_MAJOR=7 ARCH=aarch32 PLAT=stm32mp1 AARCH32_SP=sp_min DTB_FILE_NAME=stm32mp157c-<board>.dtb

Final image

Final image is available for Flash or SD card update in the corresponding folder: 

build/<target>/<debug|release>/tf-a-<target>.stm32
Ex:
build/stm32mp1/debug/tf-a-stm32mp157c-ev1.stm32

Distribution Package

For an OpenSTLinux distribution, the TF-A image is built in release mode by default. The yocto recipe can be found in:

meta-st/meta-st-stm32mp/recipes-bsp/trusted-firmware-a/tf-a-stm32mp_<version>.bb

If you want to modify the TF-A code source, use the following steps starting from an already downloaded and built OpenSTLinux distribution.

Access sources

You can use devtool to access the source. 

 PC $> cd <baseline root directory>
 PC $> devtool modify tf-a-stm32mp sources/boot/tf-a

By going to the sources/boot/tf-a folder, you can manage and modify the TF-A sources. To rebuild it, go back to the build-<distribution> folder and launch the TF-A recipe: 

 PC $> bitbake tf-a-stm32mp

The final image is deployed in the image default output folder.

Update software on board

Partitioning of binaries

The TF-A build provides a binary named tf-a-stm32mp157c-<board>.stm32 that MUST be copied to a dedicated partition named "fsblX" (X depends of needed backup).

Warning.png TF-A must be located in the first partition of your boot device.

You can just update the first partition for a simple test, but all backup partitions must contain the same image at the end.

Update via SDCARD

If you use an SD card, you can simply update TF-A using the dd command on your host.
Plug your SD card into the computer and copy the binary to the dedicated partition; on an SDCard/USB disk the "fsbl1" partition is partition 1: 

 - SDCARD: /dev/mmcblkXp1 (where X is the instance number)
 - SDCARD via USB reader: /dev/sdX1 (where X is the instance number)
  • Linux
 PC $> dd if=<tf-a file> of=/dev/<device partition> bs=1M conv=fdatasync
Info.png To find the partition associated to a specific label, just plug the

SDCARD/USB disk into your PC and call the following command: 

 PC $> ls -l /dev/disk/by-partlabel/
 total 0
 lrwxrwxrwx 1 root root 10 Jan 17 17:38 bootfs -> ../../mmcblk0p4
 lrwxrwxrwx 1 root root 10 Jan 17 17:38 fsbl1 -> ../../mmcblk0p1          ➔ FSBL1 (TF-A)
 lrwxrwxrwx 1 root root 10 Jan 17 17:38 fsbl2 -> ../../mmcblk0p2          ➔ FSBL2 (TF-A backup – same content as FSBL)
 lrwxrwxrwx 1 root root 10 Jan 17 17:38 rootfs -> ../../mmcblk0p5
 lrwxrwxrwx 1 root root 10 Jan 17 17:38 ssbl -> ../../mmcblk0p3           ➔ SSBL (U-Boot)
 lrwxrwxrwx 1 root root 10 Jan 17 17:38 userfs -> ../../mmcblk0p6
  • Windows

There is an existing dd for Windows that makes binary copying possible.

Update via USB mass storage on U-boot

See 如何在U-Boot中使用USB大容量存储

Follow the previous section to put tf-a-<board>.stm32 onto SDCard/USB disk

Update your boot device (including SD card on the target)

Refer to the STM32CubeProgrammer documentation to update your target.


<securetransclude src="ProtectedTemplate:PublicationRequestId" params="12345 | 2018-10-10 | PhilipS"></securetransclude>

取自“http://wiki.100ask.org/index.php?title=STM32MP15_TF-A&oldid=7285”