如何发送或接收CAN数据
来自百问网嵌入式Linux wiki
如何发送或接收 CAN 数据
目的
- 本文介绍如何使用 can-utils [1 ]包在 SocketCAN 接口上发送/接收数据。
- can-utils 包含一些用于 Linux®SocketCAN 子系统的用户空间实用程序。它已集成在STM32微处理器系列的 SDK 中。在此示例中，仅使用到 cansend 和 candump，但软件包中还提供了许多其他的工具。
准备条件
- 至少需要两个设备才能在 CAN 网络上进行通信。要实现这种配置，请在同一 CAN 总线上连接两个设备。然后，从一个节点发送数据，并在另一节点上接收数据。
- 在开始通信之前，必须在每块板上配置并启用 SocketCAN 接口。请参阅如何设置 SocketCAN 接口。
在CAN总线上发送数据
- 要发送单个帧，请使用 cansend 实用程序：
Board $> cansend can0 123#1122334455667788- 获取 cansend 实用程序中的使用帮助信息：
Board $> cansend -h
Usage: cansend <device> <can_frame>- 如果出现帧错误，请尝试下面的操作：
<can_id>#{R|data} for CAN 2.0 frames
<can_id>##<flags>{data} for CAN FD frames
<can_id> can have 3 (SFF) or 8 (EFF) hex chars
{data} has 0..8 (0..64 CAN FD) ASCII hex-values (optionally separated by '.')
<flags> a single ASCII Hex value (0 .. F) which defines canfd_frame.flags
e.g. 5A1#11.2233.44556677.88/123#DEADBEEF/5AA#/123##1/213##311
1F334455#1122334455667788/123#R for remote transmission request.在CAN总线上接收数据
- 要实时显示总线上收到的消息列表，请使用 candump 实用程序：
Board $> candump can0
can0 123 [8] 11 22 33 44 55 66 77 88- 在 candump 实用程序上获取帮助信息：
Board $> candump -h
Usage: candump [options] <CAN interface>+
(use CTRL-C to terminate candump)
Options: -t <type> (timestamp: (a)bsolute/(d)elta/(z)ero/(A)bsolute w date)
-c (increment color mode level)
-i (binary output - may exceed 80 chars/line)
-a (enable additional ASCII output)
-S (swap byte order in printed CAN data[] - marked with '`' )
-s <level> (silent mode - 0: off (default) 1: animation 2: silent)
-b <can> (bridge mode - send received frames to <can>)
-B <can> (bridge mode - like '-b' with disabled loopback)
-u <usecs> (delay bridge forwarding by <usecs> microseconds)
-l (log CAN-frames into file. Sets '-s 2' by default)
-L (use log file format on stdout)
-n <count> (terminate after receiption of <count> CAN frames)
-r <size> (set socket receive buffer to <size>)
-D (Don't exit if a "detected" can device goes down.
-d (monitor dropped CAN frames)
-e (dump CAN error frames in human-readable format)
-x (print extra message infos, rx/tx brs esi)
-T <msecs> (terminate after <msecs> without any reception)
Up to 16 CAN interfaces with optional filter sets can be specified on the commandline in the form: <ifname>[,filter]*
Comma separated filters can be specified for each given CAN interface:
<can_id>:<can_mask> (matches when <received_can_id> & mask == can_id & mask)
<can_id>~<can_mask> (matches when <received_can_id> & mask != can_id & mask)
#<error_mask> (set error frame filter, see include/linux/can/error.h)
[j|J] (join the given CAN filters - logical AND semantic)
CAN IDs, masks and data content are given and expected in hexadecimal values.
When can_id and can_mask are both 8 digits, they are assumed to be 29 bit EFF.
Without any given filter all data frames are received ('0:0' default filter).
Use interface name 'any' to receive from all CAN interfaces.
Examples:
candump -c -c -ta can0,123:7FF,400:700,#000000FF can2,400~7F0 can3 can8
candump -l any,0~0,#FFFFFFFF (log only error frames but no(!) data frames)
candump -l any,0:0,#FFFFFFFF (log error frames and also all data frames)
candump vcan2,92345678:DFFFFFFF (match only for extended CAN ID 12345678)
candump vcan2,123:7FF (matches CAN ID 123 - including EFF and RTR frames)
candump vcan2,123:C00007FF (matches CAN ID 123 - only SFF and non-RTR frames)硬件自检
- 在内部环回测试模式下，FDCAN将发送的消息作为接收消息进行处理。此选项用于硬件自检（无需在 CAN 总线上连接外部 CAN 节点）。
- 要在回环模式下配置和启用 SocketCAN，请执行以下操作：
Board $> ip link set can0 up type can bitrate 1000000 dbitrate 2000000 fd on loopback on
[ 78.700698] m_can 4400e000.can can0: bitrate error 0.3%
[ 78.704568] m_can 4400e000.can can0: bitrate error 1.6%
[ 78.710140] IPv6: ADDRCONF(NETDEV_CHANGE): can0: link becomes ready- 要在同一接口上发送和接收消息，请按照下列步骤操作：
Board $> candump can0 -L &
[1] 475
Board $> cansend can0 300#AC.AB.AD.AE.75.49.AD.D1
(1539944874.949723) can0 300#ACABADAE7549ADD1
(1539944874.949683) can0 300#ACABADAE7549ADD1参考
- CAN-UTILS信息，github.com上的README
