U-Boot overview

Das U-Boot

Das U-Boot (“通用引导加载程序”或U-Boot) 是一种开源引导加载程序，可用于ST板上以初始化平台并加载Linux^® 内核。

官方网站： https://www.denx.de/wiki/U-Boot
官方手册： project documentation 和 https://www.denx.de/wiki/DULG/Manual
官方的源代码 可在 git 存储库下找到[1]

 PC $> git clone https://gitlab.denx.de/u-boot/u-boot.git

在开始使用U-Boot之前，请阅读README | |}} README file 。它涵盖以下主题：

源文件树结构
配置定义说明
关于构建U-Boot的说明
Hush外壳的简要说明
常用环境变量列表

U-Boot overview

Zoom out to STM32MPU Embedded Software

同一个U-Boot源可以生成SPL和U-Boot中使用的两个固件 STM32 MPU boot chain:

受信任的引导链：TF-A作为FSBL，U-Boot作为SSBL
基本启动链：SPL作为FSBL，U-Boot作为SSBL

基本启动链不能用于产品开发 (请参见Boot chains overview 以获取详细信息).

它仅作为最简单的SSBL的示例提供，并支持上游U-Boot开发。但是，当SPL与U-Boot中提供的用于基本引导链的最小安全监视器结合使用时，已经发现了几个已知的限制。它们适用于:

功率
安全访问寄存器
有限的功能(STM32CubeProgrammer / boot from NAND Flash memory).

没有针对这些限制的修复计划。

SPL: FSBL for basic boot

U-Boot SPL 或 SPL 是 the basic boot chain的第一阶段引导加载程序（FSBL）。
它是从U-Boot源生成的小二进制文件（引导实用程序），并存储在内部有限大小的嵌入式RAM中。SPL的主要功能如下：

它由ROM代码加载。
它执行初始的CPU和板配置（时钟和DDR内存）。
它将SSBL(U-Boot)加载到DDR内存中。

U-Boot: SSBL

U-Boot 是STM32 MPU平台的默认第二阶段引导程序（SSBL）。它同时用于 trusted and basic引导链

SSBL的主要功能如下：

它是可配置和消耗的。
它具有一个简单的命令行界面（CLI），允许用户通过串行端口控制台进行交互。
它提供脚本功能
它将内核加载到RAM中并控制内核
它管理多个内部和外部设备，例如NAND和NOR闪存，以太网和USB。
它支持以下功能和命令：
- 文件系统：FAT, UBI/UBIFS, JFFS
- IP堆栈：FTP
- 显示： LCD, HDMI, BMP for splashcreen
- USB: host (mass storage) or device (DFU stack)

SPL phases

SPL 在SYSRAM中执行以下主要阶段：

board_init_f(): 驱动程序初始化，包括DDR初始化（最小堆栈和堆：CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN）
DDR内存中堆的配置(CONFIG_SPL_SYS_MALLOC_F_LEN)
board_init_r(): 初始化在SPL设备树中激活的其他驱动程序
加载并执行U-Boot(或Falcon模式下的内核^[1]: doc/README.falcon | |}} README.falcon ).

U-Boot phases

U-Boot 在DDR内存中执行以下主要阶段：

Pre-relocation 初始化 (common/board_f.c): 在CONFIG_SYS_TEXT_BASE加载地址上运行的最小初始化（例如CPU，时钟，重置，DDR和控制台）
Relocation: 将代码复制到DDR内存的末尾。
Post-relocation initialization:(common/board_r.c): 初始化所有驱动程序。
Command execution 通过自动引导(CONFIG_AUTOBOOT)或控制台shell
- 启动命令的执行（默认情况下 bootcmd=CONFIG_BOOTCOMMAND）：
  例如，将命令bootm执行到：
  - 加载并检查映像（例如内核，设备树和ramdisk）
  - 修复内核设备树
  - 安装安全监视器（可选）或
  - 将控制权传递给Linux内核(或另一个目标应用程序)

U-Boot configuration

U-Boot二进制配置基于

Kbuild infrastructure (与Linux Kernel, 您可以在U-Boot中使用make menuconfig )
配置基于以下各项：
- 在 Kconfig 文件中定义的选项(CONFIG _ compilation 标志)
- 所选配置文件：configs/ | |}} configs/stm32mp*_defconfig
other compilation flags 定义于include/configs/ | |}} include/configs/stm32mp*.h (这些标志将逐步迁移到Kconfig)
文件名通过CONFIG_SYS_CONFIG_NAME配置。
对于 {{#vardefine:info|}}{{#vardefine:dev|MP15x lines}}{{#vardefine:info| }}STM32{{#var:dev}}{{#var:info}}, 使用了include/configs/stm32mp1.h | |}} include/configs/stm32mp1.h 文件。

DeviceTree: U-Boot和SPL二进制文件包括在运行时解析的设备树blob

所有的配置标志(前缀为 CONFIG_)都在源代码中描述，或者在 README | |}} README 文件中，或者在doc/ | |}} documentation directory 目录中。
例如，CONFIG_SPL激活SPL编译
因此，为了选择一个预定义的配置，需要为主板编译 U-Boot，select the <target> 和 the device tree 。
有关示例，请参阅#U-Boot_build。

Kbuild

与内核一样，U-Boot构建系统也基于 configuration symbols (在Kconfig文件中定义). 选定的值存储在build目录的.config文件中，具有相同的Makefile目标。
按照以下步骤进行:

选择预定义的配置(configs/ | |}} configs directory 中的defconfig文件) 并生成第一个 .config:

 PC $> make <config>_defconfig.

使用以下五个make 命令之一更改U-Boot编译配置(修改.config)：

 PC $> make menuconfig --> menu based program
 PC $> make config  --> line-oriented configuration
 PC $> make xconfig --> QT program^[2]
 PC $> make gconfig --> GTK program
 PC $> make nconfig --> ncurse menu based program

然后，您可以使用更新的.config编译U-Boot。

Warning: 修改是在构建目录的本地执行的。在 make distclean 之后它将丢失.

保存您的配置以将其用作defconfig文件：

  PC $> make savedefconfig

此目标将当前配置保存为build目录中的defconfig文件。然后可以将其与预定义的配置进行比较(configs/stm32mp*defconfig).

其他makefile目标如下：

  PC $> make help
 ....
 Configuration targets:
   config	  - Update current config utilising a line-oriented program
   nconfig         - Update current config utilising a ncurses menu based
                     program
   menuconfig	  - Update current config utilising a menu based program
   xconfig	  - Update current config utilising a Qt based front-end
   gconfig	  - Update current config utilising a GTK+ based front-end
   oldconfig	  - Update current config utilising a provided .config as base
   localmodconfig  - Update current config disabling modules not loaded
   localyesconfig  - Update current config converting local mods to core
   defconfig	  - New config with default from ARCH supplied defconfig
   savedefconfig   - Save current config as ./defconfig (minimal config)
   allnoconfig	  - New config where all options are answered with no
   allyesconfig	  - New config where all options are accepted with yes
   allmodconfig	  - New config selecting modules when possible
   alldefconfig    - New config with all symbols set to default
   randconfig	  - New config with random answer to all options
   listnewconfig   - List new options
   olddefconfig	  - Same as oldconfig but sets new symbols to their
                    default value without prompting

Device tree

请参阅doc/README.fdt-control | |}} doc/README.fdt-control 以获取详细信息。

板设备树具有与内核相同的绑定。它集成在SPL和U-Boot二进制文件中：

默认情况下，它被附加在代码的末尾(CONFIG_OF_SEPARATE).
它嵌入在U-Boot二进制文件（CONFIG_OF_EMBED）中。这对调试很有用，因为它可以轻松加载.elf文件。

defconfig文件中有一个默认的设备树（通过设置CONFIG_DEFAULT_DEVICE_TREE）。

您可以使用DEVICE_TREE make标志选择另一个受支持的设备树。对于stm32mp板，相应的文件为： arch/arm/dts/ | |}} arch/arm/dts/stm32mp*.dts .

  PC $> make DEVICE_TREE=<dts-file-name>

或提供预编译的设备树blob(using EXT_DTB option):

  PC $> make EXT_DTB=boot/<dts-file-name>.dtb

SPL设备树也从该设备树生成。但是为了减小其大小，U-Boot生成文件使用fdtgrep工具来解析完整的U-Boot DTB并识别SPL所需的所有驱动程序。

为此，U-Boot使用特定的设备树标志来定义相关的驱动程序是否在U-Boot重定位之前初始化和/或相关的节点是否存在于SPL中：

u-boot,dm-pre-reloc => 存在于SPL中，在U-Boot中重新定位之前初始化
u-boot,dm-pre-proper => 在U-Boot中重新定位之前初始化
u-boot,dm-spl => 存在于SPL中

在U-Boot使用的设备树中，这些标志需要添加到SPL或U-Boot中使用的每个节点中，然后再进行重定位以及每个使用的句柄（时钟，复位，引脚控制）。

U-Boot command line interface (CLI)

请参阅 U-Boot Command Line Interface.

如果CONFIG_AUTOBOOT已激活，则在显示以下行并执行bootcmd(CONFIG_BOOTCOMMAND)后，您有CONFIG_BOOTDELAY秒(默认情况下为2秒)通过按任意键进入控制台：

 Hit any key to stop autoboot:  2

Commands

这些命令在cmd/ | |}} cmd/*.c . 通过相应的 CONFIG_CMD_* 配置标志激活它们。

使用U-Boot shell中的help 命令列出设备上可用的命令：

 Board $> help

以下是从中提取的所有命令的列表 U-Boot Manual (不详尽):

Information Commands
- bdinfo - 打印板信息结构
- coninfo - 打印控制台设备和信息
- flinfo - 打印闪存信息
- iminfo - 打印应用程序映像的标题信息
- help - 打印在线帮助
Memory Commands
- base - 打印或设置地址偏移量
- crc32 - 校验和计算
- cmp - 内存比较
- cp - 内存拷贝
- md - 内存显示
- mm - 内存修改(自动递增)
- mtest - 简单的RAM测试
- mw - 内存写入(填充)
- nm - 内存修改（常量地址）
- loop - 地址范围内无限循环
Flash Memory Commands
- cp - 内存复制
- flinfo - 打印闪存信息
- erase - 清除闪存
- protect - 启用或禁用闪存写入保护
- mtdparts - 定义与Linux兼容的MTD分区方案
Execution Control Commands
- source - 从内存运行脚本
- bootm - 从内存启动应用程序映像
- go - 在地址‘addr’处启动应用程序
Download Commands
- bootp - 使用BOOTP / TFTP协议通过网络引导映像
- dhcp - 调用DHCP客户端以获得IP /启动参数
- loadb - 通过串行线加载二进制文件（kermit模式）
- loads - 通过串行线加载S-Record文件
- rarpboot- 使用RARP/TFTP协议通过网络引导映像
- tftpboot- 使用TFTP协议通过网络引导映像
Environment Variables Commands
- printenv- 打印环境变量
- saveenv - 将环境变量保存到永久存储
- setenv - 设置环境变量
- run - 在环境变量中运行命令
- bootd - 启动默认设置，即运行‘bootcmd’
Flattened Device Tree support
- fdt addr - 选择要处理的FDT
- fdt list - 打印等级一级
- fdt print - 递归打印
- fdt mknode - 创建新节点
- fdt set - 设置节点属性
- fdt rm - 删除节点或属性
- fdt move - 将FDT blob移动到新地址
- fdt chosen - 固定动态信息
Special Commands
- i2c - I2C子系统
Storage devices
Miscellaneous Commands
- echo - 将参数返回到控制台
- reset - 执行CPU重置
- sleep - 将执行延迟预定义的时间
- version - 打印监视器版本

要添加新命令，请参阅doc/README.commands | |}} doc/README.commands .

U-Boot environment variables

U-Boot行为是通过环境变量配置的。

环境变量请参阅Manual 和README | |}} README 。

On the first boot, U-Boot uses a default environment embedded in the U-Boot binary. You can modify it by changing the content of CONFIG_EXTRA_ENV_SETTINGS in your configuration file (for example ./include/configs/stm32mp1.h) (see README | |}} README / - Default Environment).

This environment can be modified and saved in the boot device. When it is present, it is loaded during U-Boot initialization:

for e•MMC/SD card boot (CONFIG_ENV_IS_IN_EXT4), in the bootable ext4 partition "bootfs" in
in file CONFIG_ENV_EXT4_FILE="uboot.env".
for NAND boot (CONFIG_ENV_IS_IN_UBI), in the two UBI volumes "config" (CONFIG_ENV_UBI_VOLUME) and "config_r" (CONFIG_ENV_UBI_VOLUME_REDUND).
for NOR boot (CONFIG_ENV_IS_IN_SPI_FLASH), in the u-boot_env mtd parttion (at offset CONFIG_ENV_OFFSET).

env command

The env command allows displaying, modifying and saving the environment in U-Boot console.

 Board $> help env
 env - environment handling commands
 
 Usage:
 env default [-f] -a - [forcibly] reset default environment
 env default [-f] var [...] - [forcibly] reset variable(s) to their default values
 env delete [-f] var [...] - [forcibly] delete variable(s)
 env edit name - edit environment variable
 env exists name - tests for existence of variable
 env print [-a | name ...] - print environment
 env print -e [name ...] - print UEFI environment
 env run var [...] - run commands in an environment variable
 env save - save environment
 env set -e name [arg ...] - set UEFI variable; unset if 'arg' not specified
 env set [-f] name [arg ...]

Example: proceed as follows to restore the default environment and save it. This is useful after a U-Boot upgrade:

 Board $> env default -a
 Board $> env save

bootcmd

"bootcmd" variable is the autoboot command. It defines the command executed when U-Boot starts (CONFIG_BOOTCOMMAND).

For stm32mp, CONFIG_BOOTCOMMAND="run bootcmd_stm32mp":

 Board $> env print bootcmd    
  bootcmd=run bootcmd_stm32mp

"bootcmd_stm32mp" is a script that selects the command to be executed for each boot device (see ./include/configs/stm32mp1.h), based on generic distro scripts:

for serial/usb: execute the stm32prog command.
for mmc boot (e•MMC, SD card), boot only on the same device (bootcmd_mmc...).
for nand boot, boot with on ubifs partition on nand (bootcmd_ubi0).
for nor boot, use the default order e•MMC (SDMMC 1)/ NAND / SD card (SDMMC 0) / SDMMC2 (the default bootcmd: distro_bootcmd).

 Board $> env print bootcmd_stm32mp

You can then change this configuration:

either permanently in your board file (default environment by CONFIG_EXTRA_ENV_SETTINGS or change CONFIG_BOOTCOMMAND value) or
temporarily in the saved environment:

 Board $> env set bootcmd run bootcmd_mmc0 
 Board $> env save

Note: To reset the environment to its default value:

 Board $> env default bootcmd
 Board $> env save

Generic Distro configuration

Refer to doc/README.distro | |}} doc/README.distro for details.

This feature is activated by default on ST boards (CONFIG_DISTRO_DEFAULTS):

one boot command (bootmcd_xxx) exists for each bootable device.
U-Boot is independent of the Linux distribution used.
bootcmd is defined in ./include/config_distro_bootcmd.h | |}} ./include/config_distro_bootcmd.h

When DISTRO is enabled, the command that is executed by default is include/config_distro_bootcmd.h| |}} include/config_distro_bootcmd.h :

 bootcmd=run distro_bootcmd

This script tries any device found in the 'boot_targets' variable and executes the associated bootcmd.

Example for mmc0, mmc1, mmc2, pxe and ubifs devices:

 bootcmd_mmc0=setenv devnum 0; run mmc_boot
 bootcmd_mmc1=setenv devnum 1; run mmc_boot
 bootcmd_mmc2=setenv devnum 2; run mmc_boot
 bootcmd_pxe=run boot_net_usb_start; dhcp; if pxe get; then pxe boot; fi
 bootcmd_ubifs0=setenv devnum 0; run ubifs_boot

U-Boot searches for a extlinux.conf configuration file for each bootable device. This file defines the kernel configuration to be used:

bootargs
kernel + device tree + ramdisk files (optional)
FIT image

U-Boot scripting capabilities

"Script files" are command sequences that are executed by the U-Boot command interpreter. This feature is particularly useful to configure U-Boot to use a real shell (hush) as command interpreter.

See U-Boot script manual for an example.

U-Boot build

Prerequisites

a PC with Linux and tools:
- see PC_prerequisites
- #ARM cross compiler
U-Boot source code
- the latest STMicroelectronics U-Boot version
  - tar.xz file from Developer Package (for example STM32MP1)
  - from GITHUB^[3], with git command

 PC $> git clone https://github.com/STMicroelectronics/u-boot

from the Mainline U-Boot in official GIT repository ^[4]

 PC $> git clone https://gitlab.denx.de/u-boot/u-boot.git

ARM cross compiler

A cross compiler ^[5] must be installed on your Host (X86_64, i686, ...) for the ARM targeted Device architecture. In addition, the $PATH and $CROSS_COMPILE environment variables must be configured in your shell.

You can use gcc for ARM, available in:

the SDK toolchain (see Cross-compile with OpenSTLinux SDK)
PATH and CROSS_COMPILE are automatically updated.
an existing package
For example, install gcc-arm-linux-gnueabihf on Ubuntu/Debian: (PC $> sudo apt-get.
an existing toolchain:
- latest gcc toolchain provided by arm (https://developer.arm.com/open-source/gnu-toolchain/gnu-a/downloads/)
- gcc v7 toolchain provided by linaro: (https://www.linaro.org/downloads/)

For example, to use gcc-arm-9.2-2019.12-x86_64-arm-none-linux-gnueabihf.tar.xz from arm, extract the toolchain in $HOME and update your environment with:

 PC $> export PATH=$HOME/gcc-arm-9.2-2019.12-x86_64-arm-none-linux-gnueabihf/bin:$PATH
 PC $> export CROSS_COMPILE=arm-none-linux-gnueabihf-

For example, to use gcc-linaro-7.2.1-2017.11-x86_64_arm-linux-gnueabi.tar.xz
from https://releases.linaro.org/components/toolchain/binaries/7.2-2017.11/arm-linux-gnueabi/
Unzip the toolchain in $HOME and update your environment with:

 PC $> export PATH=$HOME/gcc-linaro-7.2.1-2017.11-x86_64_arm-linux-gnueabi/bin:$PATH
 PC $> export CROSS_COMPILE=arm-linux-gnueabi-

Compilation

In the U-Boot source directory, select the <target> and the <device tree> for your configuration and then execute the make all command:

 PC $> make <target>_defconfig
 PC $> make DEVICE_TREE=<device-tree> all

Optionally KBUILD_OUTPUT can be used to change the output directory to compile several targets or not to compile in the source directory. For example:

 PC $> export KBUILD_OUTPUT=../build/basic

DEVICE_TREE can also be exported to your environment when only one board is supported. For example:

 PC $> export DEVICE_TREE=stm32mp157c-ev1

Examples from STM32MP15 U-Boot:

Three configurations are supported for {{#vardefine:info|}}{{#vardefine:dev|MP15x lines}}{{#vardefine:info| }}STM32{{#var:dev}}{{#var:info}}:

stm32mp15_trusted_defconfig: trusted boot chain, U-Boot (without SPL) is unsecure and uses Secure monitor from TF-A
stm32mp15_optee_defconfig: trusted boot chain, U-Boot (without SPL) is unsecure and uses Secure monitor from SecureOS = OP-TEE
stm32mp15_basic_defconfig: basic boot chain, with an SPL as FSBL, U-BOOT is secure and installs monitor with PSCI

The board diversity is only managed with the device tree.

 PC $> export KBUILD_OUTPUT=../build/trusted
 PC $> make stm32mp15_trusted_defconfig
 PC $> make DEVICE_TREE=stm32mp157c-<board> all

 PC $> export KBUILD_OUTPUT=../build/optee
 PC $> export DEVICE_TREE=stm32mp157c-<board>
 PC $> make stm32mp15_optee_defconfig
 PC $> make all

 PC $> make stm32mp15_basic_defconfig
 PC $> make DEVICE_TREE=stm32mp157c-<board>  all

Use help to list other targets:

 PC $> make help

Output files

The resulting U-Boot files are located in your build directory (U-Boot or KBUILD_OUTPUT).

Two binary formats are used for stm32mp devices:

STM32 image format (*.stm32), managed by mkimage U-Boot tools and Signing_tool. It is requested by ROM code and TF-A (see STM32 header for binary files for details).
uImage (*.img) format, file including a U-Boot header, managed by SPL and U-Boot (for kernel load)

The U-Boot generated files are the following

For Trusted boot chain (TF-A is used as FSBL, with or without OP-TEE)
- u-boot.stm32 : U-Boot binary with STM32 image header, loaded by TF-A

For Basic boot chain (SPL is used as FSBL)
- u-boot-spl.stm32 : SPL binary with STM32 image header, loaded by ROM code
- u-boot.img : U-Boot binary with uImage header, loaded by SPL

The files used to debug with gdb are

u-boot : elf file for U-Boot
spl/u-boot-spl : elf file for SPL

References

[1] ttps://www.denx.de/wiki/pub/U-Boot/MiniSummitELCE2013/2013-ELCE-U-Boot-Falcon-Boot.pdf

[2] ttps://en.wikipedia.org/wiki/Xconfig

[3] ttps://github.com/STMicroelectronics/u-boot

[4] ttps://gitlab.denx.de/u-boot/u-boot.git or https://github.com/u-boot/u-boot

[5] ttps://en.wikipedia.org/wiki/Cross_compiler

[1]

[2]

[3]

[4]

[5]

匿名

搜索

U-Boot overview

名字空间

更多

页面选项

目录

Das U-Boot

U-Boot overview

SPL: FSBL for basic boot

U-Boot: SSBL

SPL phases

U-Boot phases

U-Boot configuration

Kbuild

Device tree

U-Boot command line interface (CLI)

Commands

U-Boot environment variables

env command

bootcmd

Generic Distro configuration

U-Boot scripting capabilities

U-Boot build

Prerequisites

ARM cross compiler

Compilation

Output files

References

导航

导航

所有产品

Wiki工具

Wiki工具

匿名

搜索

U-Boot overview

目录

Das U-Boot

U-Boot overview

SPL: FSBL for basic boot

U-Boot: SSBL

SPL phases

U-Boot phases

U-Boot configuration

Kbuild

Device tree

U-Boot command line interface (CLI)

Commands

U-Boot environment variables

env command

bootcmd

Generic Distro configuration

U-Boot scripting capabilities

U-Boot build

Prerequisites

ARM cross compiler

Compilation

Output files

References

导航

Wiki工具

页面工具

分类