How to use SPI

或许可以给这篇文章改个名字:

• 准确地说，这是针对Linux的 ?
• 如何从userland使用SPI？(使用 "spidev": SPI设备用户空间API)

我们需要总结一下吗?

Purpose

本文介绍如何使用SPI。SPI overview 文章中描述了SPI概述。

本文介绍了将外围设备分配给Linux®时如何使用SPI

• 如何通过板设备树配置SPI设备（使用“ spidev”的示例）
• 如何在用户区中执行数据传输

也许可以细化为TOC

• 1 目的
• 2 配置（DT，内核，板卡连接)
• 3 用户领域的数据传输

SPI Loop between MOSI and MISO

也许在这里添加几行来说明SPI循环的重要性 同意，看起来像是这里的示例，但对自定义SPI用户登陆有效吗？ 详细说明...
也可以在 #Simple data transfer之前移动 短路SPI总线的MISO和MOSI线以建立环回，使总线可以接收其发送的相同数据。 快速执行基本测试和执行性能测试很有趣。

Board connections

Merge this into previsous description? Redundant with above Connect the MISO and MOSI lines...

A wire has to be added to connect MISO and MOSI pins (D12 et D11 pins on STM32MP157X-DKX ARDUINO connector)

Maybe add level2 "Configuration" chapter as pre-requisite:

• DT config board
• kernel menuconfig (SPI_SPIDEV), link to #Kernel configuration or mention here:

Device Drivers --->
   SPI support --->
       <*>   User mode SPI device driver support

DT configuration (board level)

Board DT configuration has to be updated to:

• configure cs-gpios and activate spi4 node
• add spidev configuration to spi4 node

<securetransclude src="ProtectedTemplate:ReviewsComments" params="W1935: ABO: The properties #addess-cells and #size-cells are not required in the spi device. They are mandatory in the spi controller node, and in fact they are correctly present in stm32mp157c.dtsi, but not in the spi device. This is described in Documentation/devicetree/bindings/spi/spi-bus.txt"></securetransclude>{{#set:Has reviews comments=true}} <securetransclude src="ProtectedTemplate:ReviewsComments" params="W1938 FGA: Don't understand why you copy/paste the example already provided in SPI_device_tree_configuration#DT_configuration_-28board_level-29. There's no additional information here... Or maybe need to add better explanation on why it has to be updated for loopback testing ?

• Configure the PE11 GPIO as the chip select by using cs-gpios ...
• Configure the SPI MOSI/MISO/... pin as alternate function via pinctrl through pinctrl-0, pinctrl-1 and pinctrl-names
• Activate SPI controller by setting status "okay"
• Add a spidev child node
  • Enable spidev by adding compatible "spidev";
  • Configure speed by setting ...
  • Also a note on unit-address (@0) / reg <0> / cs-gpio index/number?;"></securetransclude>{{#set:Has reviews comments=true}}

&spi4 {
	pinctrl-names = "default", "sleep";
	pinctrl-0 = <&spi4_pins_a>;
	pinctrl-1 = <&spi4_sleep_pins_a>;
	status = "okay";
	cs-gpios = <&gpioe 11 0>;

	spidev@0{
		compatible = "spidev";
		reg = <0>;
		spi-max-frequency = <4000000>;
		#address-cells = <1>;
		#size-cells = <0>;
	};
};

Simple data transfer

Board $> echo -ne "\xAA\xBB" > /dev/spidev0.0
Board $> more /dev/spidev0.0
<securetransclude src="ProtectedTemplate:ReviewsComments" params="W1938 FGA: command result ? How to check it matches spi4 instance ?"></securetransclude>{{#set:Has reviews comments=true}}

Data transfer with spidev_test

The spidev_test tool, from the Linux^® kernel, provides a test tool for spidev.

Source code location

The Linux^® kernel spidev_test tool source code can be found under tools/spi.

spidev_test compilation

This tool is not compiled by default when compiling the Linux kernel for the target board. It can be compiled independently: 如何构建Linux内核用户空间工具 and then installed on the target.

List the spidev options

The spidev_test tool options can be listed:

Board $> spidev_test -h
Usage: spidev_test [-DsbdlHOLC3vpNR24SItx]
  -D --device   device to use (default /dev/spidev1.1)
  -s --speed    max speed (Hz)
  -d --delay    delay (usec)
  -b --bpw      bits per word
  -i --input    input data from a file (e.g. "test.bin")
  -o --output   output data to a file (e.g. "results.bin")
  -l --loop     loopback
  -H --cpha     clock phase
  -O --cpol     clock polarity
  -L --lsb      least significant bit first
  -C --cs-high  chip select active high
  -3 --3wire    SI/SO signals shared
  -v --verbose  Verbose (show tx buffer)
  -p            Send data (e.g. "1234\xde\xad")
  -N --no-cs    no chip select
  -R --ready    slave pulls low to pause
  -2 --dual     dual transfer
  -4 --quad     quad transfer
  -S --size     transfer size
  -I --iter     iterations
  -t --txonly   simplex tx transfer
  -r --rxonly   simplex rx transfer

Example to transfer 32 bytes in full-duplex

Board $> spidev_test -D /dev/spidev0.0 -v
			spi mode: 0x0
			bits per word: 8
			max speed: 500000 Hz (500 KHz)
			TX | FF FF FF FF FF FF 40 00 00 00 00 95 FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF F0 0D  | ......@.... .................. .
			RX | FF FF FF FF FF FF 40 00 00 00 00 95 FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF F0 0D  | ......@.... .................. .

References