“I2C device tree configuration”的版本间的差异

来自百问网嵌入式Linux wiki
第79行: 第79行:
 
{{Info| 对于高于100KHz的I2C总线频率,强烈建议使用I2C时序。}}
 
{{Info| 对于高于100KHz的I2C总线频率,强烈建议使用I2C时序。}}
  
'''For {{EcosystemRelease | revision=1.2.0 | range=and after}}'''
+
 
* '''{{highlight|st,smbus-alert}}''' optional property allow to enable the driver handling of the SMBus Alert mechanism. When enabled, the slave driver's alert function will be called whenever the slave device generates an SMBus Alert message.
+
* '''{{highlight|st,smbus-alert}}''' 可选属性允许启用驱动程序对SMBus Alert机制的处理。 启用后,只要从设备生成SMBus警报消息,就会调用从驱动程序的警报功能。
* '''{{highlight|st,smbus-host-notify}}''' optional property allow to enable the driver handling of the SMBus Host Notify mechanism. When enabled, an IRQ handler will get called whenever a slave device sends a Host Notify message.
+
* '''{{highlight|st,smbus-host-notify}}''' 可选属性允许启用驱动程序对SMBus Host Notify机制的处理。 启用后,每当从设备发送主机通知消息时,就会调用IRQ处理程序。
{{Info| See Linux smbus-protocol documentation <ref name="smbus-protocol ">{{CodeSource |Linux kernel | Documentation/i2c/smbus-protocol}}</ref> for more details about SMBus Alert & Host Notify handling.}}
+
{{Info| 请参阅Linux smbus-protocol文档 <ref name="smbus-protocol ">{{CodeSource |Linux kernel | Documentation/i2c/smbus-protocol}}</ref>了解有关SMBus警报和主机通知处理的更多详细信息。}}
  
 
==== I²C devices related properties ====
 
==== I²C devices related properties ====

2020年11月8日 (日) 14:31的版本

Article purpose

本文介绍了如何配置“ I2C内部外围设备”[1] when the peripheral is assigned to Linux® OS,尤其是:

  • 如何配置STM32 I2C外设
  • 如何配置板上或硬件扩展上存在的STM32外部I2C器件。

使用设备树机制执行配置[2].

它由“STM32 I2C Linux®驱动程序”使用,该驱动程序在 I2C框架中注册相关信息。

如果将外围设备分配给另一个执行上下文,请参阅 How to assign an internal peripheral to a runtime context 文章,以获取有关外围设备分配和配置的准则。

DT bindings documentation

I2C表示为:

  • “I2C总线的通用设备树绑定”[3]
  • “STM32 I2C控制器设备树绑定”[4]

DT configuration

该硬件描述是STM32微处理器设备树文件(扩展名为.dtsi)和板子设备树文件(扩展名为.dts)的组合。 有关设备树文件分割的说明,请参见Device tree

STM32CubeMX可用于生成板卡设备树。有关更多详细信息,请参考How to configure the DT using STM32CubeMX

DT configuration (STM32 level)

在设备级,I2C控制器声明如下:

i2c2: i2c@40013000 {
	compatible = "st,stm32f7-i2c";
	reg = <0x5c002000 0x400>;
	interrupt-names = "event", "error", "wakeup";
	interrupts-extended = <&intc GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>,
			      <&intc GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>,
			      <&exti 22 1>;
	clocks = <&rcc I2C2_K>;
	resets = <&rcc I2C2_R>;
	#address-cells = <1>;
	#size-cells = <0>;
	dmas = <&dmamux1 35 0x400 0x05>,
	       <&dmamux1 36 0x400 0x05>;
	power-domains = <&pd_core>;
	st,syscfg-fmp = <&syscfg 0x4 0x2>;
	st,syscfg-fmp-clr = <&syscfg 0x44 0x2>;
	status = "disabled";
};
Warning.png 该设备树部分与STM32微处理器有关。 它必须保持原样,而不能由最终用户修改。

请参考DTS文件: stm32mp157c.dtsi[5]

DT configuration (board level)

&i2c3 {
	pinctrl-names = "default", "sleep";
	pinctrl-0 = <&i2c2_pins_a>;
	pinctrl-1 = <&i2c2_pins_sleep_a>;
	i2c-scl-rising-time-ns = <185>;
	i2c-scl-falling-time-ns = <20>;
        st,smbus-alert;
        st,smbus-host-notify;
	status = "okay";
	/delete-property/dmas;
	/delete-property/dma-names;

	ov5640: camera@3c {
         [...]
	};
};

设备树配置分为两个级别:

I²C internal peripheral related properties

与I2C内部外围设备和I2C节点所属的I²C总线相关的设备树属性

  • pinctrl-0&1 配置取决于硬件板配置以及I2C设备如何连接到SCL,SDA(如果设备符合SMBus标准,则连接到SMBA)引脚。
    有关引脚配置的更多详细信息,请参见: Pinctrl device tree configuration
  • clock-frequency代表I2C总线速度:正常(100KHz)快速(400KHz)快速+(最高 1MHz)。该值以Hz为单位。
  • dmas 默认情况下,所有I2C实例均启用DMA。如果不需要,则由用户决定是否“删除”。

/delete-property/ 用于删除I2C的DMA使用情况。要删除DMA,必须同时插入/delete-property/dma-names/delete-property/dmas

  • i2c-scl-rising/falling-time-ns是可选值,具体取决于板的硬件特性: 导线长度,电阻和电容的硬件设计。
    这些值必须以纳秒为单位提供,并且可以通过观察示波器上的SCL上升和下降斜率来测量。请参见 how to measure I2C timings.
    I2C驱动程序使用此信息根据请求的 clock-frequency来计算准确的I2C时序。
    STM32CubeMX实现了遵循I2C标准并考虑用户输入的算法。
    如果未提供这些值,则驱动程序将使用其默认值。
    提供错误的参数将产生不正确的 clock-frequency. 如果驱动程序未能根据用户输入计算时序参数(SCL上升/下降和时钟频率),则时钟频率将降级为较低的频率。示例:如果用户将400 kHz指定为时钟频率,但是算法无法为指定的SCL上升和下降时间生成时序,则时钟频率将降至100 kHz。
Info.png 对于高于100KHz的I2C总线频率,强烈建议使用I2C时序。


  • st,smbus-alert 可选属性允许启用驱动程序对SMBus Alert机制的处理。 启用后,只要从设备生成SMBus警报消息,就会调用从驱动程序的警报功能。
  • st,smbus-host-notify 可选属性允许启用驱动程序对SMBus Host Notify机制的处理。 启用后,每当从设备发送主机通知消息时,就会调用IRQ处理程序。
Info.png 请参阅Linux smbus-protocol文档 [6]了解有关SMBus警报和主机通知处理的更多详细信息。

I²C devices related properties

The device tree properties related to I²C devices connected to the specified I²C bus. Each I²C device is represented by a sub-node.

  • reg represents the I2C peripheral slave address on the bus.
    Be aware that some slave address bits can have a special meaning for the framework. For instance, the 31st bit indicates 10-bit device capability.
    Refer to i2c.txt[3] for further details

How to measure I2C timings

i2c-scl-rising-time-ns is measured on the SCL rising edge and i2c-scl-falling-time-ns on the SCL falling edge. On the oscilloscope, measure the time between the 20% to 80% range of amplitude for rising time and falling time in nanoseconds.

Alternate text
I2C timings

DT configuration examples

Example of an external EEPROM slave device

i2c4: {
    status = "okay";
    i2c-scl-rising-time-ns = <185>;
    i2c-scl-falling-time-ns = <20>;
   
    eeprom@50 {
        compatible = "at,24c256";
        pagesize = <64>;
        reg = <0x50>;
    };
};

The above example registers an EEPROM device on i2c-X bus (X depends on how many adapters are probed at runtime) at address 0x50 and this instance is compatible with the driver registered with the same compatible property.
Please note that the driver is going to use MDMA for data transfer and that SCL rising/falling times have been provided as inputs.

Example of an EEPROM slave device emulator registering on STM32 side

i2c4: {
    eeprom@64 {
        status = "okay";
        compatible = "linux,slave-24c02";
        reg = <0x40000064>;
    };
};

The above example registers an EEPROM emulator on STM32 side at slave address 0x64.
STM32 acts as an I2C EEPROM that can be accessed from an external master device connected on I2C bus.

Example of a stts751 thermal sensor with SMBus Alert feature enabled

For ecosystem release ≥ v1.2.0{{#set:Ecosystem release=revision of a previous flow 1.2.0}}
The stts751 thermal sensor [7] is able to send an SMBus Alert when configured threshold are reached.
The device driver can be enabled in the kernel:

[x] Device Drivers
    [x] Hardware Monitoring support
        [x] ST Microelectronics STTS751

This can be done manually in your kernel:

CONFIG_SENSORS_STTS751=y

Since the SMBus Alert is relying on a dedicated pin to work, the pinctrl of the I2C controller (here i2c2) must be updated to add the corresponding SMBA pin.

For the i2c2 controller:

i2c2_pins_a: i2c2-0 {
    pins {
        pinmux = <STM32_PINMUX('H', 4, AF4)>, /* I2C2_SCL */
                        <STM32_PINMUX('H', 5, AF4)>, /* I2C2_SDA */
                        <STM32_PINMUX('H', 6, AF4)>; /* I2C2_SMBA */
        bias-disable;
        drive-open-drain;
        slew-rate = <0>;
    };
};

i2c2_pins_sleep_a: i2c2-1 {
    pins {
        pinmux = <STM32_PINMUX('H', 4, ANALOG)>, /* I2C2_SCL */
                        <STM32_PINMUX('H', 5, ANALOG)>, /* I2C2_SDA */
                        <STM32_PINMUX('H', 6, ANALOG)>; /* I2C2_SMBA */
    };
};

Within the device-tree, the st,smbus-alert property must be added, as well as the node to enable the stts751.

i2c2: {
    st,smbus-alert;
    stts751@3b {
        status = "okay";
        compatible = "stts751";
        reg = <0x3b>;
    };
};

How to configure the DT using STM32CubeMX

The STM32CubeMX tool can be used to configure the STM32MPU device and get the corresponding platform configuration device tree files.
The STM32CubeMX may not support all the properties described in the above DT bindings documentation paragraph. If so, the tool inserts user sections in the generated device tree. These sections can then be edited to add some properties and they are preserved from one generation to another. Refer to STM32CubeMX user manual for further information.