“How to calibrate the touchscreen”的版本间的差异
Zhouyuebiao(讨论 | 贡献) |
Zhouyuebiao(讨论 | 贡献) |
||
第1行: | 第1行: | ||
− | + | Touchscreen is more precise after a calibration, but this action is not mandatory. | |
− | [[Category: | + | Calibration data are erased after each firmware download into STMicroelectronics boards. |
+ | |||
+ | The steps described below have to be performed on a running board : | ||
+ | {{ReviewsComments|JCT w905: it would have been nice to have these lines already, per default, in weston.ini. Maybe, a future improvement?}} | ||
+ | * Edit and change the value of the ''touchscreen_calibrator'' to '''true''' in the ''libinput'' section of the ''weston.ini'' Weston configuration file<ref name="weston.ini">[http://manpages.ubuntu.com/manpages/wily/man5/weston.ini.5.html Ubuntu weston.ini manpage]</ref>. ''#[libinput'' shall be uncommented. | ||
+ | |||
+ | {{Board$}} vi /etc/xdg/weston/weston.ini | ||
+ | [...] | ||
+ | [libinput] | ||
+ | touchscreen_calibrator=true | ||
+ | calibration_helper=/bin/echo | ||
+ | [...] | ||
+ | |||
+ | * Restart weston | ||
+ | |||
+ | {{Board$}} systemctl restart weston | ||
+ | |||
+ | * List all the touchscreen devices | ||
+ | {{Board$}} weston-touch-calibrator | ||
+ | could not load cursor 'dnd-move' | ||
+ | could not load cursor 'dnd-copy' | ||
+ | could not load cursor 'dnd-none' | ||
+ | device "/sys/devices/platform/soc/40012000.i2c/i2c-0/0-002a/input/input1/event1" - head "DSI-1" | ||
+ | |||
+ | * Launch calibration with the input of the touch panel | ||
+ | |||
+ | {{Board$}} weston-touch-calibrator /sys/devices/platform/soc/40012000.i2c/i2c-0/0-002a/input/input1/event1 | ||
+ | |||
+ | If the calibration succeeds, no message will be displayed on the console. If it fails, the following message will appear: | ||
+ | {{Board$}} weston-touch-calibrator error: Calibration verification failed, too large error. | ||
+ | |||
+ | Touchscreen identifier may vary, depending on the devices that are connected to the board. Recommendation is to unplug all the additional input devices before booting. Otherwise, it is up to You to adapt the command line. | ||
+ | |||
+ | ==References== | ||
+ | <references /> | ||
+ | |||
+ | <noinclude> | ||
+ | {{PublicationRequestId | Auto}} | ||
+ | [[Category:How to run use cases]] | ||
+ | [[Category:Wayland Weston]] | ||
+ | </noinclude> |
2020年5月8日 (五) 22:54的最新版本
Touchscreen is more precise after a calibration, but this action is not mandatory.
Calibration data are erased after each firmware download into STMicroelectronics boards.
The steps described below have to be performed on a running board : <securetransclude src="ProtectedTemplate:ReviewsComments" params="JCT w905: it would have been nice to have these lines already, per default, in weston.ini. Maybe, a future improvement?"></securetransclude>{{#set:Has reviews comments=true}}
- Edit and change the value of the touchscreen_calibrator to true in the libinput section of the weston.ini Weston configuration file[1]. #[libinput shall be uncommented.
Board $> vi /etc/xdg/weston/weston.ini [...] [libinput] touchscreen_calibrator=true calibration_helper=/bin/echo [...]
- Restart weston
Board $> systemctl restart weston
- List all the touchscreen devices
Board $> weston-touch-calibrator could not load cursor 'dnd-move' could not load cursor 'dnd-copy' could not load cursor 'dnd-none' device "/sys/devices/platform/soc/40012000.i2c/i2c-0/0-002a/input/input1/event1" - head "DSI-1"
- Launch calibration with the input of the touch panel
Board $> weston-touch-calibrator /sys/devices/platform/soc/40012000.i2c/i2c-0/0-002a/input/input1/event1
If the calibration succeeds, no message will be displayed on the console. If it fails, the following message will appear:
Board $> weston-touch-calibrator error: Calibration verification failed, too large error.
Touchscreen identifier may vary, depending on the devices that are connected to the board. Recommendation is to unplug all the additional input devices before booting. Otherwise, it is up to You to adapt the command line.
References
<securetransclude src="ProtectedTemplate:PublicationRequestId" params="Auto | |"></securetransclude>